Using the froth Select
The froth Select Automatic Milk Frother comes equipped with a milk pitcher with lid, two frothing disks, one heating disk and the base unit. One of the disks is installed inside the milk pitcher. The other disk and the heating disk are stored underneath the base of the appliance.
Before First Use
Clean the milk pitcher and the disks under running warm water. Make sure the underside of the milk pitcher is completely dry.
CAUTION: Maximum Capacity - FROTHING: never fill more than 16-oz (see MAX marking inside milk pitcher)
Maximum Capacity - HEATING: never fill more than 20-oz (see “––––” marking inside milk pitcher)
Using the Frothing Disk
Never fill more than 16-oz of milk or chocolate milk into the milk pitcher (“MAX” marking); otherwise, hot milk could spill over the milk pitcher onto the heating platform. This may damage the interior parts of the machine.
Using the Heating Disk:
For the CHOC setting, you may use the heating disk with a minimum of 8-oz of milk. Never fill more than 20-oz of milk or chocolate milk into the milk pitcher (“––––” marking)
Using the Selector Dial
The selector dial (F) will control the speed of the disk in the pitcher while the frothing or heating disk will control the milk texture of the frothed or heated milk. There is no right or wrong way to use the frothing or heating disks combined with the different settings on the selector dial. The below chart is a helpful guide, but individual results will vary depending on the type of milk used and different ingredients that are added during the frothing cycle. It is highly recommended to experiment with the different setting and disk combinations, to create your own delicious recipes.
Hot Frothing and Heating Milk
Perfect for hot beverages such as cappuccinos, lattes, hot chocolate, flat whites and milk steamers.
1. Plug in appliance.
2. Remove lid from milk pitcher. (A)
3. Place one of the frothing disks or the heating disk into the bottom of the milk pitcher. Ensure the disk is completely snapped in. (B)
4. Make sure underside of the milk pitcher is dry.
5. Pour fresh cold milk into the milk pitcher (C) and replace lid. (D)
6. Place pitcher on heating platform. (E)
7. For frothing and heating milk turn the selector dial (F) to the (HOT) FROTH or FLAT icon. When the (HOT) FROTH icon is selected the disk will rotate at a high rate of speed. When the FLAT icon is used the disk will spin at a medium rate of speed. Depending on which disk is used, this will help control the final texture of the milk once the cycle is complete. Selecting the frothing disk with the (HOT) FROTH setting will maximize the froth produced while selecting the heating disk with the FLAT option will give almost no froth but will heat/steam the milk.
8. Press the center of the selector dial and the frothing/heating action starts automatically. The dial will illuminate blue and a short beep will indicate that the cycle has begun.
9. When the milk has reached the maximum temperature, the appliance will automatically shut off. The indicator light turns off and the frothing action stops. A short beep will indicate that the end of the cycle has been reached. The cycle can always be stopped manually by pressing the center of the selector dial or lifting the pitcher from the base.
CAUTION: The milk pitcher is now very warm; the bottom of the pitcher is hot. Only place the milk pitcher on a heat resistant surface.
10. Pour the warm milk into your cup and spoon the froth on top.
11. Always unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance.
Cold Frothing and Mixing Milk
Good for cold beverages such as iced cappuccinos, iced fruit lattes, cold malts and mixing chocolate milk. Follow steps 1 through 6 above in “Hot Frothing and Heating Milk.”
Note: For the best cold frothing or cold mixing results, it is recommended to use the frothing disk.
1. For cold frothing or cold mixing (incorporating chocolate syrup into milk, mixing malt powder, etc.) turn the selector dial (F) to the (COLD) FROTH setting.
2. Press the center of the selector dial and the frothing/mixing action starts automatically. The dial will illuminate blue and a short beep will indicate that the cycle has begun.
3. Once the frothing disk starts spinning, you may add any ingredients like chocolate syrup, malt powder, etc.
4. After a few minutes, the appliance will automatically shut off. The indicator light turns off and frothing stops. A short beep will indicate that the end of the cycle has been reached. The cycle can always be stopped manually by pressing the center of the selector dial or lifting the pitcher from the base.
5. Pour milk into cup and spoon froth on top.
6. Always unplug from outlet when not in use and before cleaning.
Making Hot Chocolate
The froth Select features a special hot chocolate function that allows chocolate chunks or chocolate chips to be added directly to the pitcher. The heating disk will rotate slowly, allowing the chocolate to gently mix and heat. You may also add grated chocolate, chocolate syrup or powdered hot chocolate mix directly to the milk pitcher. Follow steps 1 through 6 above in “Hot Frothing and Heating Milk.”
Note: For the best hot chocolate results, it is recommended to use the heating disk. A minimum of 8-oz of milk should be used, otherwise the milk may burn. A maximum of 16-oz may be used with the CHOC setting.
1. For hot chocolate turn the selector dial (F) to the CHOC setting.
2. Press the center of the selector dial and the frothing/heating action starts automatically. The dial will illuminate blue and a short beep will indicate that the cycle has begun.
3. After a few minutes of heating the illuminated dial will start to blink, and a series of short beeps will indicate that it is time to add the chocolate into the milk pitcher.
Note: Once the illuminated dial starts to blink, it will continue blinking for approximately one minute. Once the light becomes solid, stop adding chocolate and replace the lid. This will help to ensure that the chocolate melts completely into the milk before the end of the cycle.
4. Remove the lid from the pitcher and gradually add small chunks of chocolate, chocolate chips, grated chocolate or powdered hot chocolate mix into the pitcher. For the best results, add the chocolate slowly by dropping it in small amounts along the edge of the milk pitcher, away from the rotating disk. It is not recommended to add more than 113 grams (4-oz) of chocolate or powdered hot chocolate mix to the pitcher for one cycle.
Note: If chocolate chunks are left in pitcher after the cycle stops you may need to use smaller pieces. For best results, try to add all of the chocolate while the light is blinking, otherwise the chocolate may not have time to fully melt into the milk.
5. After a few minutes, the appliance will automatically shut off. The indicator light turns off and the mixing action stops. A short beep will indicate that the end of the cycle has been reached. The cycle can always be stopped manually by pressing the center of the selector dial or lifting the pitcher from the base.
6. Pour hot chocolate into cup and enjoy!
7. Always unplug from outlet when not in use and before cleaning.
Tips for using the froth Select:
• When adding extra ingredients such as chocolate, smaller pieces will melt more easily than larger pieces. “Chocolate chips” commonly found in the baking section of most supermarkets work well.
• Always add extra ingredients along the edge of the pitcher, away from the rotating disk.
• Always add extra ingredients gradually to help avoid interrupting the cycle.
• It is best to used shaved or grated chocolate when using the (HOT) FROTH setting, as the smaller pieces are less likely to become stuck in the frothing disk as it rotates at a higher rate of speed. Use the CHOC setting when adding larger ingredients like chocolate chunks or chocolate chips.
• If the frothing disk becomes stuck and makes a loud noise, press the center of the selector dial to stop the cycle. Remove the lid and use a small spoon to gently mix the ingredients. Press the center of the selector dial to restart the cycle.
Please note:
• When you remove the milk pitcher from the appliance during operation, the appliance will automatically shut off. When replacing the pitcher, you need to press the center of the selector dial to start the cycle again.
• If the heating plate or the bottom of the milk pitcher is still hot, the appliance may not turn on. In this case, remove the milk pitcher. Cool it down by running the bottom of the pitcher under cold water. Make sure the bottom of the pitcher is dry and start over.
CAUTION: Do not place the milk pitcher in the microwave or on any other heating surface.
Types of Milk
All kinds of milk can be used with this appliance (Whole, 2%, 1%, skim, soy milk, almond milk, rice milk, etc.) Skim milk will produce the thickest, most stable froth. Soy milk will produce froth with somewhat larger bubbles, but the froth is not as stable. Always use milk that is as fresh as possible, to achieve the best results.
Cleaning
1. Unplug the appliance and let it cool down.
2. Remove the frothing disk or the heating disk from the milk pitcher. Clean under running warm water.
3. The milk pitcher and lid are dishwasher safe (top-rack).
4. Wipe the heating plate with a moist cloth.
5. Discoloration of the heating plate may occur if milk spills onto the heating plate. Scrub lightly with baking soda.
Frothing / Heating Disk Storage
One disk can be kept inside the milk pitcher. The two other disks can be stored underneath the base of the appliance.
Additional Milk Pitcher and Disks
Order an additional milk pitcher or disks by calling Customer Service at:
1-800-767-3554 or by visiting www.capresso.com.
